STG (Skid-To-GO)

REVERSE OSMOSIS SYSTEM
Model: STG (Skid-To-Go)
800 to 14,400+ GPD

STANDARD FEATURES

  • Reverse Osmosis Membrane
  • Twin tank water softener w/auto backwash
  • Carbon filter w/auto backwash
  • 24gpm ultraviolet water sterilizer, s.s.
  • 1hp s.s. repressurization
  • TDS blending valve
  • Powder-coated steel frame
  • Stainless steel multi-stage pump
  • Stainless steel membrane vessel
  • High-pressure nylon tubing
  • Liquid-filled high pressure gauge
  • Inlet/Outlet pre-filter gauges
  • Liquid-tight wire shrouding
  • Feed water inlet solenoid valve
  • Adjstbl. waste & recycle s.s. needle valves
  • Product / waste flow meters
  • 10″ 5 micron BB pre-filter
  • High-pressure brass comp. fittings
  • 300 gallon water storage tank

STANDARD ELECTRICAL CONTROLS:

    • 4-line LCD display
    • Keypad
    • Menu system
    • Temperature display
    • TDS monitor
    • Tank full
    • Low pressure
  • Hour meter
  • Time delay start
  • System ON / OFF
  • Dual-level control
  • Fully-fused

OPTIONS:

  • Blending valve
  • Throttle valve
  • Recycle flow meter
  • 20″ BB pre-filter
  • 20″ BB post-filter
  • 3phase motor w/IEC
  • 50hz Motor
  • Auto hourly flush
  • Feed water TDS monitor
  • Pre-treatment lock-out
  • Product diversion
  • Permeate purge
  • Hi-pressure cut-off

 

MODEL *GPD MEMBRANE MOTOR OPERATING
PRESSURE
110V-
60HZ
AMPS
220V-
60HZ- 1hp
AMPS
RECOVERY
RATE
PIPING
inlet   waste   prod
DIMENSIONS
weight lbs.
STG-880S
STG-800
850+
800+
4″x21″
4″x21″
.75hp
.75hp
150psi
200psi
10.4
10.4
5.2
5.2
50-60% 1/2″  3/8″  3/8″
FPT   FPT   FPT
56″X34″X66″
494 lbs
STG-1S
STG-1
1,800+
1,600+
4″x40″
4″x40″
.75hp
1.5hp
150psi
200psi
11.6
20.0
5.8
10.4
50-70% 3/4″  1/2″  1/2″
FPT   FPT   FPT
56″x34″x66″
750 lbs
STG-2S
STG-2
3,600+
3,170+
4″x40″
4″x40″
.75hp
1.5hp
150psi
200psi
11.6
20.0
5.8
10.4
50-70% 3/4″  1/2″  1/2″
FPT   FPT   FPT
66″x34″x66″
782 lbs
STG-3S
STG-3
5,400+
4,750+
4″x40″
4″x40″
7.5hp
1.5hp
150psi
200psi
11.6
20.0
5.8
10.4
50-70% 3/4″  1/2″  1/2″
FPT   FPT   FPT
66″x34″x66″
810 lbs
STG-4S
STG-4
7,200+
6,340+
4″x40″
4″x40″
2hp
3hp
150psi
200psi
19.2
n/a
9.8
13
50-70% 3/4″  1/2″  1/2″
FPT   FPT   FPT
66″x34″x66″
852 lbs
STG-5S
STG-5
9,000+
7,900+
4″x40″
4″x40″
2hp
3hp
150psi
200psi
19.2
n/a
9.8
13
50-70% 3/4″  1/2″  1/2″
FPT   FPT   FPT
66″x34″x66″
883 lbs
STG-6S
STG-6
10,800+
9,500+
4″x40″
4″x40″
2hp
3hp
150psi
200psi
19.2
n/a
9.8
13
50-70% 3/4″  1/2″  1/2″
FPT   FPT   FPT
66″x34″x66″
910 lbs
STG-8S
STG-8
14,400+
12,670+
4″x40″
4″x40″
3hp
3hp
150psi
200psi
n/a
n/a
13
13
50-70% 3/4″  1/2″  1/2″
FPT   FPT   FPT


FEED WATER PARAMETERS:

  • Temperature: 85° F maximum
  • Pressure: 40 – 80 psi maximum
  • TDS: 2000-5000 ppm maximum (Consult Dealer for specific model)
  • Iron tolerance: 0.5 ppm maximum
  • Hydrogen sulfide: must be removed
  • Silica tolerance: can not be higher than 100 ppm in the concentrate stream.
    (Antiscalant should be considered for any levels over 75 ppm)
  • Turbidity: should be removed
  • Hardness: must be removed


OPERATING PARAMETERS:

  • Operating pressure: 150 – 200 psi maximum
  • Water recovery: up to 70% and is field adjusted by customer.
    (It is not recommended that the recovery be set higher than 70%)
  • pH range: 3 – 11
  • Flow rates are determined by the membrane mfg.’s. testing criteria of 1500 ppm Nacl solution, 77°F water temperature, 225 psi at 10-15% recovery. Typical membrane salt rejection is 95-99%

*Actual flow rates may vary depending on the pre-treatment used, water conditions, feed water temperature and applied pressure, etc.